|
Wendt X3 . 3-Channel Mixer
A high-quality, full-function, portable, 3-channel audio mixer!
 |
|
The new X3 brings the exceptional reliability and build quality of the Wendt X4 and X5 mixers into the smaller realm of a three-channel audio mixer.
This premium low-noise mixer has all the features necessary for recording top quality sound for any film or television application. The X3 can be linked to the X5
mixer for a full eight channels of reality TV mixing.
The inputs are mic or line switchable and phantom power is available on all three inputs. The X3 also offers pan switches, a slate mic and a 1/4” headphone jack,
and unbalanced AUX and balanced XLR mic-line switchable outputs. Six AA batteries give you an estimated 12-15 hours of use.
One-year limited warranty.
CE qualified
|
Technical Specifications
Size: 140mm x 158mm x 51mm (5.5 in. x 6.225 in. x 2 in.)
Weight: 0.86 Kg (1.9 lbs.)
Temperature Range: -20 to +70C
Batteries: 6 x AA, estimated use 12-15 hours
Frequency Response: 25-20kHz
Noise: EIN-128dBV
Low-Cut Filter: 100Hz, 140Hz, 12db/octave
Return: 3.5mm stereo jack
Distortion: Less than 0.1% THD
Mic Powering: 48v PH and Dynamic
Mic-Line Input: Switchable
Tone Oscillator:
400 Hz, 0dB VU
Line Output: Balanced XLR mic-line, switchable
Aux Output: Unbalanced TA5 mic-line, switchable
Link Output:
Link to Wendt X5 for 8 matched channels
Other Features: Limiter, PAN switches, external power (9-18v), slate mic, phone jack (1/4 in.), blue LED display brightness switch.
|
|
|
Click on the images below for a closer view...
Front Panel
- Channel Faders — Channel 1, 2 and 3 correspond to the mic inputs (1,2, & 3)
- Stereo VU Display (LED) — Blue LEDs -12dB, -9dB, -6dB, -3dB, 0dB and red LED +3dB
- Low Cut Filters — The three position switch, 140HZ, 20HZ, and 100HZ at 12dB per octave
- Pan Switches — Channel 1, 2, and 3 channel 3 pan switches (right, center and left)
- Reference Tone — 0dBVU 400HZ low distortion sine wave
- Slate Mic — Low noise slate mic to right and left outputs
- Power Monitor — LED flashes on and off for normal power (voltage) and continuously on for low power
- Battery Test Switch — Battery voltage is indicated on the right LED display
- Power Switch — Mixer powering INT (batteries), EXT (external power) and OFF
- RTN Mix Switch — Switches phones from external source to mixerv HP Monitor Switch — CTR = Stereo, RT = Right Ear (R+L), LT = Left Ear (L+R)
Left Side Panel
- Mic Inputs, Channel 1, 2, and 3 — XLR electronically balanced
- Mic Powering — 48 phantom and dynamic
- Mic-Line Switch — MIC or LINE (-50dB attenuation)
- Preamplifier Gain — Switchable attenuation 10dB, 20dB and 0dB
- HP Volume — Headphone volume control
- VU LED — Switchable display brightness: bright (sunlight), normal, and off
- Limiter — Limiter in/out switchable
Right Side Panel
- Phone Jack — 1/4” stereo
- Slate Volume — Screwdriver volume adjustment
- XLR Mic-Line Outputs — Right and left line outputs, switchable MIC or LINE levels
- External Power — Mixer powering from an external DC power source of 9-18VDC (Hirose 4-pin connector, pin 4 +V, pin 1 -V)
- Return — 3.5mm stereo jack
- LINK/AUX OUT — 5-pin TA connector; link to Wendt X5 Mixer (pin 1 right, pin 3 left); AUX OUT (pin 2 right, pin 4 left), switchable (AUX switch) MIC-LINE. AUX
outputs can be configured to Mono Out by shorting Right to Left pins in mating connector.
- Battery Compartment — Six AA batteries
To Operating Instructions...
|
