|
Features and Specification - SQN-4S Series IVe
|
|
Mixer Inputs
|
Four transformerless balanced inputs using XLR-3 type female connectors. Channels one and two also share an XLR-5 type connector. Each channel is switchable for:
- Powering:
- a) 12V T (Din AB)
- b) 12V Phantom
- c) 48V Phantom
- d) Dynamic (150 to 600 Ohms)
- Attenuation:
- 0dB, -10dB or -20dB
An extra 10dB of attenuation is automatically introduced when mic powering is selected.
This is achieved without compromising the noise performance of the microphone.
- Bass Cut:
- Flat, -3dB at 75 or 105Hz
- Line Attenuation:
- Adds 50dB attenuation before the mic preamp.
|
|
Sensitivity
|
-78dBu for nominal line level (PPM4, 0VU) with the channel gain at maximum and the master gain at 0dB
|
|
Max Level, Mic Inputs
|
-20dBu (+4dBu with full attenuation)
|
|
Noise Figure
|
-130dBu (A weighted) from a 200 Ohm source.
|
|
Frequency Response
|
20Hz to 20kHz +0, -1dB, referred to 1kHz.
|
|
Crosstalk
|
Isolation, channel to unrelated channel: 75dB at 1kHz, 60dB at 15kHz.
|
|
Channel Configuration
|
The mixer has four input channels, all of which have the same input selectors, bass cuts and attenuators. The routing arrangements for CH1 & 2 differ from those for CH3
& 4.
|
|
Channels 1 & 2 [GANG 1-2]
|
The operation of the CH1, CH2 pair is controlled by the GANG 1-2 switch on the front panel. This switch has three positions:
- Twin MONO [O] in which the channels are unganged and each input channel can be routed to either or both of the
output channels.
- Stereo [S] ganging in which the Channel 1 fader controls the gain of both channels and a stereo balance control
on the side panel comes into play.
- Mid-Side [MAT] ganging in which the Channel 1 fader controls the gain of both channels and the Channel 2 fader
acts as an image width control. The incoming signal is assumed to be in MS format and is matrixed to AB. The stereo balance control remains active and will balance the matrixed signal.
|
|
Phase Switch
|
Channel 2 can have its phase inverted by means of a front panel switch. This has the incidental effect of interchanging left and right in an MS encoded signal.
|
|
Channels 3 & 4
|
The operation of the CH3, CH4 pair is much simpler than the CH1, CH2 pair. Each channel can be routed to LEFT, RIGHT or to a PANpot.
|
|
|
|
|
Monitor Return Input
|
Balanced inputs with a range of sensitivity from -20dBu to +20dBu for loudness parity with the internal monitoring. The sensitivity is adjusted by a screwdriver preset on
the base.
|
|
Mixing Bus Inputs
|
Two inputs directly into the summing amplifiers with their gain adjustable inside the mixer. Maximum sensitivity is 0dBu for +8dBu at the balanced outputs with the master
gain set at 0.
|
|
Balanced Outputs
|
Two line driver amplifiers provide the output channels and each output is available on both an individual XLR and a combined 12-way connector.
|
|
Output Attenuators
|
The level at either set of connectors can be attenuated by 50dB to provide a nominally microphone level feed.
|
|
Line Drivers
|
Floating sources (transformer coupled) with a clipping level of +20dBm into 600 Ohms. Distortion at the nominal peak level of +8dBm is less than 0.01% with a 600 Ohm load
20Hz to 20kHz. The output resistance is 60 Ohms.
The balanced Mic-Level sends are derived from separate windings on the output transformers. Their source impedance of 200 Ohms is essentially resistive
.
|
|
Unbalanced Outputs
|
A SUBSIDIARY I/O connector carries separately buffered outputs at a line
level of -10dBu.
|
|
Post-Fader Outputs,
All Channels
|
The SUBSIDIARY I/O connector carries four buffered outputs at a line
level of -10dBu.
If an external link is made on the connector, the operation of the signal routing
for channels three and four is changed so that they may be switched out of the mixing bus. Selecting PAN for CH3 or CH4 will now switch the channel out of the mix instead of to the PANpot. This is for
the benefit of those who wish to extract the channels separately.
|
|
Meters
|
Twin peak reading, logarithmic level meters with Peak Programme Meter (PPM) dynamics. Scaling may be BBC PPM, Nordic Norm, or SMPTE.
VU meters can also be provided. The meters are normally calibrated with the mixer driving a bridging load of 10k Ohms. While the mixer is operating the meters are illuminated by low power light emitting diodes.
|
|
Line Output Level
|
The nominal line level is normally set at 0dBu for PPM metered mixers and +4dBu for VU metered mixers. Peak level, which is used as a reference for the limiters, is
considered to be 8dB above this setting. Other calibration levels are readily available to order.
|
|
|
|
|
Output Limiters
|
[O]ff [M]ono [S]tereo (ganged) Attack time constant 0.5ms, release time 100ms. The limiter range is 20dB. An LED for each output channel indicates
limiter action. This Graph shows the entry into limiting on a steady signal for a nominal peak level of 8dBu
|
|
Line-up Tone
|
The Line-up tone is a sine wave at 1kHz with distortion below 0.1% which is inserted into both channels, displacing the audio output. When the [GANG 1-2] switch is in
either of the ganged positions, the left hand channel tone is interrupted for 250ms every 3s. The tone switch on the front panel is a three position toggle, shared with the Slating Microphone.
|
|
Monitoring
|
Amplifiers with adjustable gain capable of driving most types of headphone to a suitable level. Headphones with a resistance of around 200 Ohms per side will make best use
of battery power. Pre-Fade listening to each of the input channels is possible as is MS matrixing of the two output channels so that an MS recording may be monitored in the equivalent AB stereo.
|
|
Monitoring Mode Selector
|
The monitoring mode rotary selector switch on the front panel [PHONES] has the following functions.
- S Stereo
- R Right Channel
- L Left Channel
- MS MS Matrix (MS stereo equivalent)
- L-R Left minus Right (MS stereo equivalent Right)
- L+R Left plus Right
(MS stereo equivalent Left or Phase Check)
|
|
Monitoring Source Selector
|
A front panel toggle switch selects the monitoring source as either internal [MXR] or external [AUX]
|
|
Pre-Fade Listen
|
A pair of front panel toggle switches selects Pre-Fade Listen for channels 1 or 2 and 3 or 4. The switches are three position, centre off.
|
|
|
|
|
Slating Microphone
|
A microphone is mounted behind the front panel near the centre of the mixer. When in use, the output of the microphone is levelled by a 2:1 compressor and displaces the
normal audio, appearing on the mixer outputs and in the monitoring system. While the microphone is active, the monitoring mode automatically reverts to the internal or [MXR] setting. The Slating
Microphone switch on the front panel is a three position toggle, shared with the Line-up tone.
|
|
Batteries
|
Eight AA size cells housed in a quick-change compartment. The acceptable range of voltages is 6 to 24 Vdc allowing the use of most cell technologies.
|
|
Battery Drain
|
135mA at 12 Vdc with unpowered mics. Battery life with alkaline cells will be about 10 hours.
|
|
Battery Test
|
The right channel meter is fitted with a suppressed-zero scale, brought into operation by a front panel push button.
|
|
External
Power
|
A supply in the range 6 to 24 Vdc may be used. The maximum consumption will be 2.5W and quiescent consumption, without microphones, 1.6W. The input terminals float with
respect to ground. Either (or neither) side may be grounded at will, thereby allowing the use of floating supplies or grounded supplies of either polarity. There will be no possibility of hum-loops being
formed.
|
|
Power Distribution
|
The mixer carries two four-way connectors, one of which [DC] gives access to the internal batteries for charging and also serves to connect to an external power
source. The second connector [PT] is an output which provides a switched, short circuit proof connection to the power supplied to [DC]. This allows the mixer to be used as the focal point
for a system of interconnected devices, all controlled from the mixer’s power switch.
|
|
Temperature Range
|
The mixer is designed to work over the temperature range of -20 to +60 °C.
|
|
Dimensions
|
The dimensions of the mixer case are: Height 47mm, Width 297mm, Depth 161mm
|
|
Construction
|
The outer case of the mixer is made of aluminium. The end blocks holding the connectors and the panpots are milled from solid aluminium bar. Inside the mixer is an inner
compartment of steel, tin-plated after forming, which contains all of the circuitry that might be sensitive to radio frequency interference. The top and bottom of this compartment are sealed by copper
screens and r.f. gasket material and all inputs to and outputs from this compartment are filtered. The circuitry is constructed on multi-layer printed circuit boards with internal ground and power planes
which ensure the integrity of the internal grounding system.
All control knobs are special to SQN and are turned and milled from solid aluminium bar. The internal battery compartment is milled and bored from a solid block of
polyacetal engineering plastics material and the moving parts are aluminium and stainless steel.
All labels and legends on the mixer are permanent. On the end blocks they are engraved; on the front panel they are printed into the hard-anodised surface; on the baseplate
they are reverse printed on a polycarbonate label.
The mechanical construction is a development of a system which has proven in the past to be resistant to mechanical damage.
|
|
|
|
Weight
|
The weight of the mixer without batteries is 2.2kg
|
