 |
||||
|
|
|
 |
|
|
||||||||||||||||||||||||||||||
|
The following is a selection of available accessories for Schoeps microphones.
With the CCM, the capsule and the microphone amplifier form a non-detachable unit. Instead of using speech capsules, the active low-cut filters LC 60 U (60 Hz cut-off frequency) or the LC 120 U (120 Hz cut-off frequency) can be inserted in the microphone’s cable path.
This elastic suspension holds a compact microphone securely by a metal clamp with thumb wheel. The low weight of 190g, including a windscreen, leads to an extraordinarily light weight at the end of the boom and
easy handling. (The windscreen is not included.) The 3/8” internal thread fits any readily available microphone boom. Colour: black.
Not intended for use with larger, heavier windscreens. Diameter: 61 mm
Miniature Cable Hanger - HC This accessory is used when hanging a CCM -U type microphone. Incorporated in its design is the SGC swivel which allows orientation to any angle laterally, and vertically to any angle from 0° to 100°. There is very little danger of the CCM twisting (e.g. as a result of rising temperature) after it has been suspended. The HC is suitable only for use with the CCM-U because of the cable diameter. If used with the CCM-L, which has a thinner cable, the mounting should be secured additionally with adhesive tape. Colour: grey For use especially on pressure-gradient transducers in wind. The foam encloses an air chamber around the capsule, similar to a basket windscreen. It is highly efficient, yet it has only a slight influence on the sound. When using active accessories, as when using a compact microphone CCM, please be careful to place the W5D all the way onto the capsule. Note that the W5D cannot be used with CCM 4 V, CCM 41 V, CCM 4 VXS, or CCM 8 microphones. Dimensions: sphere with diameter 90 mm Colour: black, with additional black, porous velvet-like surface treatment. Windscreen for a single CCM-L - WSR 100 LU
The cable from the CCM and the output cable join together at the small “ConnBox.” The output cable is permanently connected to this box, but the cable from the CCM itself is attached by means of a miniature connector. This allows the rapid exchange of the cable when necessary. The assembly includes basket, suspension, cable with cable box (inside), XLR-3M output connector. A Windjammer cover is available as an option. This fur-like “overcoat” enhances the efficiency.
Similar to the WSR 100 but allows the suspension of two microphones in the same assembly with a small increase in basket size. The angle between the two microphones is adjustable to 0°(M/S), 70°, 90°, 105° or 120°. A windjammer is available as an option.
These are adjustable from 0° through 100° in either direction. The internal thread of the SGC or SGCM screws onto any 3/8” rod or stand adapter. Its swivel permits the capsule to be offset at any angle from 0° to 100°. SGC (right) has clamp made of grey plastic, the aesthetic version. The SGC is an integral part of several other accessories such as the HC cable hanger and the TC and TC 2 table stands(below). An SGCM is included as part of the ACA 53. Colour: grey/black Miniature Table Stand - TCg, TC 2g These elegant table stands, with vibration-isolating base, can be placed unobtrusively. The microphone angle may be freely adjusted. The vertical rod is removable, allowing the microphone to be mounted on the base close to the mounting surface.
Dimensions: See also the alternative T2/C2 twin table microphones. Low-cut Filters - LC 60 U (60 Hz)/LC 120 U (120 Hz) Active high-pass filters for phantom-powered microphones, in particular CCM and CMC
Under extreme conditions the LC 120 U can be used, though it may have an audible effect on the sound of a voice. Both filters can help prevent overloading the input circuit to which a microphone is connected – a problem which occurs more often than many people realise. The specifications of the Schoeps microphones (sensitivity, noise, source impedance) remain nearly unchanged with the LC. These low-cut filters are suitable not only for Schoeps microphones but also for phantom-powered microphones of other manufacturers, provided that they have a minimum current consumption of 2 mA. Otherwise the maximum sound-pressure level would be reduced. Please note: Technical Specifications
Filter: Butterworth, 18 dB/oct. Cut-off frequency (-3dB): LC 60 U: 60 Hz LC 120 U: 120 Hz A maximum of two filters may be used in series, which then results in 36 dB/octave slope. Output impedance: 40 Ohms at 1 kHz with Schoeps CCM or CMC Gain: 0 dB Maximum output voltage: approx. 1 V when 4mA current is being drawn Diameter: 20mm Length: 94mm
Surface finish: Nickel |
|||||||||||||||||||||||||||||||
Elastic Miniature Suspension with Swivel - 
A neat cable run is obtained when the cable is put into the wire loop between the bolt and the socket. (The microphone and cable to be ordered separately.)
These electronic filters can be inserted anywhere in the microphone
cable path. With a roll-off of 18 dB/ octave, the LC 60 U suppresses low-frequency acoustic interference (e.g. wind noise, or solid-borne infrasonic sound such as handling noise during boom operation)
without detracting from the sound quality of voice recordings. |
|
 |
|
|
| [LTF Home] [Products] [Contact Us] |
|